Ericsson RX1290 Guide de l'utilisateur Page 58
- Page / 136
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Operating the Equipment Remotely
Page 4-4 Reference Guide: RX1290 H.264 Contribution Receiver
ST.RE.E10228.1
Table 4.2: Configuring the Serial Remote Port and Activating Remote Protocol
Step Action Result
1. Go to menu 7.1. Displays ‘OPERATING MODE’.
2. Press Edit. Displays ‘FRONT PANEL’.
3.
Press the down pushbutton and select
‘SERIAL REMOTE’.
The settings should be set to match the external control host.
4. Press Save. The unit is ready for Remote Control.
Once the communication parameters are entered correctly, set the system into remote mode
for the external computer to gain control of the unit:
Step Action Result
1. Go to menu 7.1.2. Displays ‘SERIAL REMOTE PROTOCOL’.
2. Press Edit. Toggle between RS-232 Alteia or RS-485 Alteia.
3.
Chose between RS-232 Alteia or RS-485
Alteia.
The settings should be set to match the external control host.
4. Press Save. The unit is ready for Remote Control.
4.1.5 Configuring the Unit For Remote Control Over-air
Overview
For the unit to be controlled via over-air control (OAC), the control mode of the Contribution
Receiver needs to be set to Director NCP.
Table 4.3: Activating Director NCP Remote Control
Step Action Result
1. Go to menu 7.1. Displays ‘OPERATING MODE’.
2. Press Edit. Displays ‘FRONT PANEL’.
3.
Press the down pushbutton and select
‘DIRECTOR NCP’.
The settings should be set to match the external control host.
4. Press Save. The unit is ready for OAC.
OAC Lockout
Once the unit is in OAC control mode, it is possible for the remote control operator to issue a
local lockout command to the Receiver. This will effectively deny the local user access to
configuring the unit.
However, if a situation occurs whereby the local user needs to regain control over the unit,
without a local lockout relinquish command being sent from the OAC control PC, a four digit
Personal Identification Number (PIN) may be entered through the keypad.
CAUTION…
TANDBERG Television Customer Services Help Desk will not be able to provide you with the Local
lockout PIN, as it is uniquely created at the time of the lockout.
The user creates the PIN at lockout time. To obtain the PIN, please consult the person
responsible for the administration of the unit.
- REFERENCE GUIDE 1
- List of Contents 3
- About This Reference Guide 4
- Warnings, Cautions and Notes 5
- EMC Compliance 5
- Contact Information 6
- Technical Training 7
- Return of Equipment 7
- Technical Publications 7
- Preliminary Pages 8
- 1Introduction 9
- Introduction 10
- ST.RE.E10228.1 10
- The Equipment Models 11
- Software Version 11
- 1.2 Summary of Features 12
- Introduction 13
- 1.3 The Satellite Receiver 14
- 1.3.2 Input Connections 15
- TANDBERG 16
- 1.5 Control Modes 17
- 1.6 Guided Tour 18
- 1.6.3 Front Panel LEDs 19
- 1.6.4 Rear Panel 19
- Chapter 2 21
- Installing the Equipment 22
- 2.1 Read This First! 23
- 2.2 Preliminary Checks 24
- 2.3.1 Fixing 25
- 2.3.2 Ventilation 25
- Information 26
- 2.5.2 AC Power Supply Cord 27
- Technical Earth 28
- 2.7 Signal Connections 29
- 2.7.2 ASI/HD-SDI/SD-SDI OUT 31
- 2.7.3 CVBS 31
- 2.7.4 Audio Outputs 31
- Item Specification 32
- 2.7.5 SVGA Output (RGB HV) 33
- 2.7.6 Frame Synchronisation 33
- 2.7.7 Ethernet 34
- 2.7.8 ASI IN 34
- 2.8 Option Card Connectors 35
- Chapter 3 37
- 3.1 Powering the Equipment 39
- 3.3.1 General 40
- 3.3.2 Navigate Mode 40
- 3.3.3 Edit Mode 40
- 3.4.1 LCD Menu Descriptions 41
- 3.4.3 Entering a Menu Value 42
- 3.5.1 Using Preset Services 42
- TT1290/HWO/DVBS2/IF/CONST) 43
- Step Action Result 44
- 3.6.3 10/100BaseT IP 45
- Selecting the Audio Manually 46
- Page 3-11 47
- (Menu 4) 48
- Page 3-13 49
- 3.12 Restarting the Unit 53
- Chapter 4 55
- 4.1 Remote Control 57
- Overview 58
- OAC Lockout 58
- Entering the OAC Lockout PIN 59
- Chapter 5 61
- 5.1 Introduction 63
- 5.3 ALARM LED 63
- • EBNO 64
- Chapter 6 65
- Options 66
- (RX1290/SWO/HSETHER) 68
- Chapter 7 71
- 7.1 Routine Checks 73
- 7.2 Servicing 73
- 7.2.2 Replacement Parts 74
- 7.3.1 Introduction 74
- 7.3.2 Warranty 74
- 7.4 Fault-finding 75
- 7.6 Disposal 77
- Annex A 79
- Glossary 80
- ITU-R 81
- ITU-T 81
- Chrominance 81
- Glossary 83
- ±12 hours from UTC 91
- Annex B 93
- B.1 Output 95
- B.1.4 Performance Figures 97
- B.3 Audio Output Format 99
- Technical Specification 100
- B.3.7 Digital Audio Outputs 101
- B.4 Input Specifications 102
- Rs = Symbol-rate (Msymbol/s) 103
- LNB Power and Control 104
- B.4.3 Frame Sync Connector 105
- B.4.2 DVB-ASI Input 105
- VITS17 +/- 100mV 106
- NTC-7 comp +/- 100mV 107
- B.5.3 Data Outputs 108
- B.5.5 Alarm Connector 109
- B.6 Environmental 110
- B.8 Cable Types 111
- B.9 Compliance 112
- B.9.3 CE Marking 113
- B.9.4 C-Tick Mark 113
- Annex C 115
- C.1 LCD Menus 117
- C.2 Menu Pages - Main Menu 117
- C.3 The Menu Structure 118
- C.5.1 Overview 119
- C.5.2 Input Selection Menu 119
- C.5.3 DVB-S2 Option 120
- RX1290/HWO/DVBS2/IF/CONST) 120
- C.6 Conditional Access Menu 121
- C.7 Service Menu (Menu 3) 122
- Framesync NTSC Offset YYYYYY 123
- –199999 to +199999 123
- C.7.3 Audio 1 Menu 124
- C.7.4 Audio 2 Menu 124
- C.7.5 Audio 3 Menu 125
- C.7.6 Audio 4 Menu 125
- C.7.7 Async Data Menu 126
- C.7.8 Ethernet Data Menus 126
- C.7.9 VBI Menu 126
- C.7.10 PCR PID Menu 127
- C.7.11 Network ID Menu 127
- C.8.1 Overview 127
- C.9 Alarms Menu (Menu 6) 128
- ST.RE.E10228.1 129
- C.9.9 MER Alarm Setup Menu 130
- C.10 System Menu (Menu 7) 131
- C.10.3 System Restart Menu 132
- Annex D 133
- Annex D - Languages 134
- Annex E 135
- Menu Description Default 136
Produits connexes et manuels pour Récepteur Ericsson RX1290
Récepteur Ericsson RX8330 Spécifications
(39 pages)
(39 pages)
Récepteur Ericsson TT1222 Guide de l'utilisateur
(198 pages)
(198 pages)
(197 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.207 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels