Ericsson RX1290 Guide de l'utilisateur Page 46
- Page / 136
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Operating the Equipment Locally
Page 3-10 Reference Guide: RX1290 H.264 Contribution Receiver
ST.RE.E10228.1
3.7.2 Selecting the Video Component
Table 3.10: Selecting the Video Component
Step Action Result
1 Go to Menu 3.1 and press Edit. Select one of
the video streams or enter a video stream PID.
Selects the video component.
2 Scroll to Menu 3.1.5 and edit the parameter for
setting the response to loss of video (FREEZE
FRAME, BLACK FRAME, BLUE FRAME, NO
SYNCS, 75% BARS AND RED, BLUE PLUS
TEXT, RED PLUS TEXT). Press Save.
Perform a system restart (see Section 3.12
Restarting the Unit).
Edits the parameter for setting the response to loss of video.
3 Scroll to Menu 3.1.6 and edit the video test
pattern to be displayed. Press Save.
Edits the video test pattern to be displayed.
4 Scroll to Menu 3.1.7 and edit the parameter for
framesync enable (ENABLED or DISABLED).
Press Save.
Edits the parameter for framesync enable.
5 Scroll to Menu 3.1.7.1 and edit the PAL
framesync offset range (-199999 to +199999
pixels) and the NTSC framesync offset range
(-199999 to +199999 pixels). Press Save.
Edits the PAL framesync offset range and the NTSC framesync
offset range.
6 Scroll to Menu 3.1.11.1 and edit the
embedded audio data IDs (0X0 – 0xFFF) and
audio channel (NONE, ONE, TWO, or ONE
and TWO). Press Save.
Edits the embedded audio data IDs and audio channel.
3.7.3 Selecting the Audio Component
Introduction
Automatic audio component selection is based on component order in the PMT as follows:
• Audio 1 selects the first component in the PMT, Audio 2 selects the second component,
Audio 3 selects the third component and Audio 4 selects the fourth component.
• Audio 1 does not select the same component as Audio 2 and vice-versa when
component-PIDs are reordered in a new PMT.
• Coding type and language are manually selectable through the User PID and type
parameters.
Selecting the Audio Manually
It is possible to manually select any audio component from the active Service by using the
front panel controls or via the remote control interface. Select one of the audio components in
the list or enter the correct PID. Table 3.11 describes the procedure for selecting a
component.
- REFERENCE GUIDE 1
- List of Contents 3
- About This Reference Guide 4
- Warnings, Cautions and Notes 5
- EMC Compliance 5
- Contact Information 6
- Technical Training 7
- Return of Equipment 7
- Technical Publications 7
- Preliminary Pages 8
- 1Introduction 9
- Introduction 10
- ST.RE.E10228.1 10
- The Equipment Models 11
- Software Version 11
- 1.2 Summary of Features 12
- Introduction 13
- 1.3 The Satellite Receiver 14
- 1.3.2 Input Connections 15
- TANDBERG 16
- 1.5 Control Modes 17
- 1.6 Guided Tour 18
- 1.6.3 Front Panel LEDs 19
- 1.6.4 Rear Panel 19
- Chapter 2 21
- Installing the Equipment 22
- 2.1 Read This First! 23
- 2.2 Preliminary Checks 24
- 2.3.1 Fixing 25
- 2.3.2 Ventilation 25
- Information 26
- 2.5.2 AC Power Supply Cord 27
- Technical Earth 28
- 2.7 Signal Connections 29
- 2.7.2 ASI/HD-SDI/SD-SDI OUT 31
- 2.7.3 CVBS 31
- 2.7.4 Audio Outputs 31
- Item Specification 32
- 2.7.5 SVGA Output (RGB HV) 33
- 2.7.6 Frame Synchronisation 33
- 2.7.7 Ethernet 34
- 2.7.8 ASI IN 34
- 2.8 Option Card Connectors 35
- Chapter 3 37
- 3.1 Powering the Equipment 39
- 3.3.1 General 40
- 3.3.2 Navigate Mode 40
- 3.3.3 Edit Mode 40
- 3.4.1 LCD Menu Descriptions 41
- 3.4.3 Entering a Menu Value 42
- 3.5.1 Using Preset Services 42
- TT1290/HWO/DVBS2/IF/CONST) 43
- Step Action Result 44
- 3.6.3 10/100BaseT IP 45
- Selecting the Audio Manually 46
- Page 3-11 47
- (Menu 4) 48
- Page 3-13 49
- 3.12 Restarting the Unit 53
- Chapter 4 55
- 4.1 Remote Control 57
- Overview 58
- OAC Lockout 58
- Entering the OAC Lockout PIN 59
- Chapter 5 61
- 5.1 Introduction 63
- 5.3 ALARM LED 63
- • EBNO 64
- Chapter 6 65
- Options 66
- (RX1290/SWO/HSETHER) 68
- Chapter 7 71
- 7.1 Routine Checks 73
- 7.2 Servicing 73
- 7.2.2 Replacement Parts 74
- 7.3.1 Introduction 74
- 7.3.2 Warranty 74
- 7.4 Fault-finding 75
- 7.6 Disposal 77
- Annex A 79
- Glossary 80
- ITU-R 81
- ITU-T 81
- Chrominance 81
- Glossary 83
- ±12 hours from UTC 91
- Annex B 93
- B.1 Output 95
- B.1.4 Performance Figures 97
- B.3 Audio Output Format 99
- Technical Specification 100
- B.3.7 Digital Audio Outputs 101
- B.4 Input Specifications 102
- Rs = Symbol-rate (Msymbol/s) 103
- LNB Power and Control 104
- B.4.3 Frame Sync Connector 105
- B.4.2 DVB-ASI Input 105
- VITS17 +/- 100mV 106
- NTC-7 comp +/- 100mV 107
- B.5.3 Data Outputs 108
- B.5.5 Alarm Connector 109
- B.6 Environmental 110
- B.8 Cable Types 111
- B.9 Compliance 112
- B.9.3 CE Marking 113
- B.9.4 C-Tick Mark 113
- Annex C 115
- C.1 LCD Menus 117
- C.2 Menu Pages - Main Menu 117
- C.3 The Menu Structure 118
- C.5.1 Overview 119
- C.5.2 Input Selection Menu 119
- C.5.3 DVB-S2 Option 120
- RX1290/HWO/DVBS2/IF/CONST) 120
- C.6 Conditional Access Menu 121
- C.7 Service Menu (Menu 3) 122
- Framesync NTSC Offset YYYYYY 123
- –199999 to +199999 123
- C.7.3 Audio 1 Menu 124
- C.7.4 Audio 2 Menu 124
- C.7.5 Audio 3 Menu 125
- C.7.6 Audio 4 Menu 125
- C.7.7 Async Data Menu 126
- C.7.8 Ethernet Data Menus 126
- C.7.9 VBI Menu 126
- C.7.10 PCR PID Menu 127
- C.7.11 Network ID Menu 127
- C.8.1 Overview 127
- C.9 Alarms Menu (Menu 6) 128
- ST.RE.E10228.1 129
- C.9.9 MER Alarm Setup Menu 130
- C.10 System Menu (Menu 7) 131
- C.10.3 System Restart Menu 132
- Annex D 133
- Annex D - Languages 134
- Annex E 135
- Menu Description Default 136
Produits connexes et manuels pour Récepteur Ericsson RX1290
Récepteur Ericsson RX8330 Spécifications
(39 pages)
(39 pages)
Récepteur Ericsson TT1222 Guide de l'utilisateur
(198 pages)
(198 pages)
(197 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.124 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels